-
1 rapid traverse button
-
2 rapid traverse button
English-Russian dictionary of mechanical engineering and automation > rapid traverse button
-
3 button
1) кнопка ( управления)2) палец; штифт•- autodraw button
- binary button
- bump button
- check button
- control button
- cycle-start button
- datum button
- drive cutout button
- dual control button
- dual palm buttons
- edit button
- edit-facility button
- emergency stop button
- feed button
- inch button
- inching button
- key button
- large convex button entirely red
- light button
- locating button
- locator button
- memory button
- menu button
- mode-select button
- mushroom head button
- mushroom-shaped head button
- nose button
- palm button
- pendant button
- pickup button
- play button
- press button
- push button
- rapid traverse button
- read button
- record button
- reference button
- reset button
- rest button
- signal button
- soft button
- spherical head rest button
- start button
- starting button
- stop button
- store-event button
- switch button
- test push button
- toe button
- tool saver control button
- toolmaker's button
- trigger button
- view control buttonEnglish-Russian dictionary of mechanical engineering and automation > button
-
4 control
1) управление; регулирование || управлять; регулировать2) контроль || контролировать3) управляющее устройство; устройство управления; регулятор4) профессиональное мастерство, квалификация, техническая квалификация5) pl органы управления•"in control" — "в поле допуска" ( о результатах измерения)
to control closed loop — управлять в замкнутой системе; регулировать в замкнутой системе
- 2-handed controlsto control open loop — управлять в разомкнутой системе; регулировать в разомкнутой системе
- 32-bit CPU control
- acceptance control
- access control
- acknowledge control
- active process control
- adaptable control
- adaptive constraint control
- adaptive control for optimization
- adaptive control
- adaptive feed rate control
- adaptive quality control
- adjustable feed control
- adjustable rotary control
- adjustable speed control
- adjusting control
- adjustment control
- AI control
- air logic control
- analog data distribution and control
- analogical control
- analytical control
- application control
- arrows-on-curves control
- autodepth control
- autofeed control
- automated control of a document management system
- automated technical control
- automatic backlash control
- automatic control
- automatic editing control
- automatic gain control
- automatic gripper control
- automatic level control
- automatic process closed loop control
- automatic remote control
- automatic sensitivity control
- automatic sequence control
- automatic speed control
- automatic stability controls
- auxiliaries control
- balanced controls
- band width control
- bang-bang control
- bang-bang-off control
- basic CNC control
- batch control
- bibliographic control
- bin level control
- boost control
- built-in control
- button control
- cam control
- cam throttle control
- camshaft control
- carriage control
- Cartesian path control
- Cartesian space control
- cascade control
- C-axis spindle control
- cell control
- center control
- central control
- central supervisory control
- centralized control
- centralized electronic control
- central-station control
- changeover control
- chip control
- circumferential register control
- close control
- closed cycle control
- closed loop control
- closed loop machine control
- closed loop manual control
- closed loop numerical control
- closed loop position control
- clutch control
- CNC control
- CNC indexer control
- CNC programmable control
- CNC symbolic conversational control
- CNC/CRT control
- CNC/MDI control
- coarse control
- coded current control
- coded current remote control
- color control
- combination control
- command-line control
- compensatory control
- composition control
- compound control
- computed-current control
- computed-torque control
- computer control
- computer numerical control
- computer process control
- computer-aided measurement and control
- computer-integrated manufacturing control
- computerized control
- computerized numerical control
- computerized process control
- constant surface speed control
- constant value control
- contactless control
- contact-sensing control
- contamination control
- continuous control
- continuous path control
- continuous process control
- contour profile control
- contouring control
- conventional hardware control
- conventional numerical control
- conventional tape control
- convergent control
- conversational control
- conversational MDI control
- coordinate positioning control
- coordinate programmable control
- copymill control
- counter control
- crossed controls
- current control
- cycle control
- dash control
- data link control
- data storage control
- deadman's handle controls
- depth control
- derivative control
- dial-in control
- differential control
- differential gaging control
- differential gain control
- differential temperature control
- digital brushless servo control
- digital control
- digital position control
- digital readout controls
- dimensional control
- direct computer control
- direct control
- direct digital control
- direct numerical control
- direction control
- directional control
- dirt control
- discontinuous control
- discrete control
- discrete event control
- discrete logic controls
- dispatching control
- displacement control
- distance control
- distant control
- distributed control
- distributed numerical control
- distributed zone control
- distribution control
- dog control
- drum control
- dual control
- dual-mode control
- duplex control
- dust control
- dynamic control
- eccentric control
- edge position control
- EDP control
- electrical control
- electrofluidic control
- electromagnetic control
- electronic control
- electronic level control
- electronic speed control
- electronic swivel control
- elevating control
- emergency control
- end-point control
- engineering change control
- engineering control
- entity control
- environmental control
- error control
- error plus error-rate control
- error-free control
- external beam control
- factory-floor control
- false control
- feed control
- feed drive controls
- feedback control
- feed-forward control
- field control
- fine control
- finger-tip control
- firm-wired numerical control
- fixed control
- fixed-feature control
- fixture-and-tool control
- flexible-body control
- floating control
- flow control
- fluid flow control
- follow-up control
- foot pedal control
- force adaptive control
- forecasting compensatory control
- fork control
- four quadrant control
- freely programmable CNC control
- frequency control
- FROG control
- full computer control
- full order control
- full spindle control
- gage measurement control
- gain control
- ganged control
- gap control
- gear control
- generative numerical control
- generic path control
- geometric adaptive control
- graphic numerical control
- group control
- grouped control
- guidance control
- hairbreath control
- hand control
- hand feed control
- hand wheel control
- hand-held controls
- handle-type control
- hand-operated controls
- hardened computer control
- hardwared control
- hardwared numerical control
- heating control
- heterarchical control
- hierarchical control
- high-integrity control
- high-level robot control
- high-low control
- high-low level control
- high-technology control
- horizontal directional control
- humidity control
- hybrid control
- hydraulic control
- I/O control
- immediate postprocess control
- inching control
- in-cycle control
- independent control
- indexer control
- indirect control
- individual control
- industrial processing control
- industrial-style controls
- infinite control
- infinite speed control
- in-process control
- in-process size control
- in-process size diameters control
- input/output control
- integral CNC control
- integral control
- integrated control
- intelligent control
- interacting control
- interconnected controls
- interlinking control
- inventory control
- job control
- jogging control
- joint control
- joystick control
- just-in-time control
- language-based control
- laser health hazards control
- latching control
- lead control
- learning control
- lever control
- lever-operated control
- line motion control
- linear control
- linear path control
- linearity control
- load control
- load-frequency control
- local control
- local-area control
- logic control
- lubricating oil level control
- machine control
- machine programming control
- machine shop control
- macro control
- magnetic control
- magnetic tape control
- main computer control
- malfunction control
- management control
- manual control
- manual data input control
- manual stop control
- manually actuatable controls
- manufacturing change control
- manufacturing control
- master control
- material flow control
- MDI control
- measured response control
- mechanical control
- memory NC control
- memory-type control
- metering control
- metrological control of production field
- microbased control
- microcomputer CNC control
- microcomputer numerical control
- microcomputer-based sequence control
- microprocessor control
- microprocessor numerical control
- microprogrammed control
- microprogramming control
- milling control
- model reference adaptive control
- model-based control
- moisture control
- motion control
- motor control
- motor speed control
- mouse-driven control
- movable control
- multicircuit control
- multidiameter control
- multilevel control
- multimachine tool control
- multiple control
- multiple-processor control
- multiposition control
- multistep control
- multivariable control
- narrow-band proportional control
- navigation control
- NC control
- neural network adaptive control
- noise control
- noncorresponding control
- noninteracting control
- noninterfacing control
- nonreversable control
- nonsimultaneous control
- numerical contouring control
- numerical control
- numerical program control
- odd control
- off-line control
- oligarchical control
- on-board control
- one-axis point-to-point control
- one-dimensional point-to-point control
- on-line control
- on-off control
- open loop control
- open loop manual control
- open loop numerical control
- open-architecture control
- operating control
- operational control
- operator control
- optical pattern tracing control
- optimal control
- optimalizing control
- optimizing control
- oral numerical control
- organoleptic control
- overall control
- overheat control
- override control
- p. b. control
- palm control
- parameter adaptive control
- parameter adjustment control
- partial d.o.f. control
- path control
- pattern control
- pattern tracing control
- PC control
- PC-based control
- peg board control
- pendant control
- pendant-actuated control
- pendant-mounted control
- performance control
- photoelectric control
- physical alignment control
- PIC control
- PID control
- plugboard control
- plug-in control
- pneumatic control
- point-to-point control
- pose-to-pose control
- position/contouring numerical control
- position/force control
- positional control
- positioning control
- positive control
- postprocess quality control
- power adaptive control
- power control
- power feed control
- power-assisted control
- powered control
- power-operated control
- precision control
- predictor control
- preselective control
- preset control
- presetting control
- pressbutton control
- pressure control
- preview control
- process control
- process quality control
- production activity control
- production control
- production result control
- programmable adaptive control
- programmable cam control
- programmable control
- programmable logic adaptive control
- programmable logic control
- programmable machine control
- programmable microprocessor control
- programmable numerical control
- programmable sequence control
- proportional plus derivative control
- proportional plus floating control
- proportional plus integral control
- prototype control
- pulse control
- pulse duration control
- punched-tape control
- purpose-built control
- pushbutton control
- quality control
- radio remote control
- radium control
- rail-elevating control
- ram stroke control
- ram-positioning control
- rapid-traverse controls for the heads
- rate control
- ratio control
- reactive control
- real-time control
- reduced-order control
- register control
- registration control
- relay control
- relay-contactor control
- remote control
- remote program control
- remote switching control
- remote valve control
- remote-dispatch control
- resistance control
- resolved motion rate control
- retarded control
- reversal control
- revolution control
- rigid-body control
- robot control
- robot perimeter control
- robot teach control
- rod control
- safety control
- sampled-data control
- sampling control
- schedule control
- SCR's control
- second derivative control
- selective control
- selectivity control
- self-acting control
- self-adaptive control
- self-adjusting control
- self-aligning control
- self-operated control
- self-optimizing control
- self-programming microprocessor control
- semi-automatic control
- sensitivity control
- sensor-based control
- sequence control
- sequence-type control
- sequential control
- series-parallel control
- servo control
- servo speed control
- servomotor control
- servo-operated control
- set value control
- shaft speed control
- shape control
- shift control
- shop control
- shower and high-pressure oil temperature control
- shut off control
- sight control
- sign control
- single variable control
- single-flank control
- single-lever control
- size control
- slide control
- smooth control
- software-based NC control
- softwared numerical control
- solid-state logic control
- space-follow-up control
- speed control
- stabilizing control
- stable control
- standalone control
- start controls
- static control
- station control
- statistical quality control
- steering control
- step-by-step control
- stepless control
- stepped control
- stick control
- stock control
- stop controls
- stop-point control
- storage assignment control
- straight cut control
- straight line control
- stroke control
- stroke length control
- supervisor production control
- supervisory control
- swarf control
- switch control
- symbolic control
- synchronous data link control
- table control
- tap-depth controls
- tape control
- tape loop control
- teach controls
- temperature control
- temperature-humidity air control
- template control
- tension control
- test control
- thermal control
- thermostatic control
- three-axis contouring control
- three-axis point-to-point control
- three-axis tape control
- three-mode control
- three-position control
- throttle control
- thumbwheel control
- time control
- time cycle control
- time optimal control
- time variable control
- time-critical control
- time-proportional control
- timing control
- token-passing access control
- tool life control
- tool run-time control
- torque control
- total quality control
- touch-panel NC control
- touch-screen control
- tracer control
- tracer numerical control
- trajectory control
- triac control
- trip-dog control
- TRS/rate control
- tuning control
- turnstile control
- two-axis contouring control
- two-axis point-to-point control
- two-dimension control
- two-hand controls
- two-position control
- two-position differential gap control
- two-step control
- undamped control
- user-adjustable override controls
- user-programmable NC control
- variable flow control
- variable speed control
- variety control
- varying voltage control
- velocity-based look-ahead control
- vise control
- vision responsive control
- visual control
- vocabulary control
- vocal CNC control
- vocal numerical control
- voltage control
- warehouse control
- washdown control
- water-supply control
- welding control
- wheel control
- wide-band control
- zero set control
- zoned track controlEnglish-Russian dictionary of mechanical engineering and automation > control
-
5 screw
1) винт; болт; шуруп || завинчивать; ввинчивать; скреплять винтами или болтами2) червяк; шнек3) винтовая линия || винтовой•to screw down — завинчивать; поджимать, поджимать винтом
to screw off — отвинчивать, свинчивать
- abutment screwto screw up — завинчивать; затягивать
- actuating screw
- actuator screw
- adjuster screw
- adjusting screw
- adjusting wedge screw
- Allen screw
- Allen set screw
- anchor screw
- anchoring screw
- attachment screw
- b.b. screw
- backup screw
- ball feed screw
- ball screw
- ball-bearing screw
- ball-jointed screw
- belt screw
- bevel-pointed screw
- binder screw
- black screw
- bleed screw
- bottle screw
- brake screw
- butterfly screw
- button-head screw
- cap screw
- capstan screw
- capstan-head screw
- capstan-headed screw
- carriage lock screw
- chamfer-pointed screw
- check screw
- cheese head screw
- clamp screw
- clamping screw
- clamp-up screw
- closing screw
- coarsely-pitched screw
- coarse-pitch screw
- collar head cap screw
- commercial screw
- compound screw
- compression screw
- cone point set screw
- cone-locking screw
- conical-nosed screw
- connecting screw
- countersunk screw
- coupler screw
- coupling screw
- cover screw
- cross-feed screw
- cross-lead screw
- cross-recessed head screw
- cross-slot head screw
- cross-slotted head screw
- cross-traverse screw
- cup head screw
- cup nibbed head screw
- cup point set screw
- cupped point set screw
- cutter blade screw
- dial screw
- differential screw
- dog point set screw
- double-ended threaded screw
- double-shoulder screw
- double-threaded screw
- downfeed screw
- drive screw
- driving screw
- eared screw
- eccentric screw
- ejection plate screw
- ejector screw
- elevating screw for adjusting the cross-rail
- endless screw
- engaging screw
- expansion screw
- eye screw
- fastening screw
- feed screw
- feeding screw
- female screw
- filister head screw
- filling screw
- fine pitch screw
- fine setting screw
- fitting screw
- fixing screw
- flange screw
- flat filister head screw
- flat head screw
- flat pivot point screw
- flat point set screw
- fluted socket screw
- fly screw
- fly-headed screw
- focusing screw
- foot screw
- forcing screw
- French head screw
- full dog point set screw
- gib screw
- governing screw
- grub screw
- guide screw
- half-bright screw
- half-dog point set screw
- hand screw
- headless screw
- head-operating screw
- helical screw
- hexagon set screw
- hexagon socket head screw
- hexagon socket set screw
- hexagon-head screw
- high-pitch screw
- Hindley screw
- hold-down screw
- holding screw
- hook screw
- horizontal feed screw
- hunter's screw
- inside screw
- instrument-headed screw
- jack screw
- knee-elevating screw
- knurled head screw
- knurled knob screw
- knurled thumb screw
- lag screw
- latch screw
- lead screw
- leading screw
- leveling screw
- limit screw
- lock screw
- locking screw
- longitudinal feed screw
- long-pitch screw
- low-head screw
- lubricating screw
- machine screws
- male screw
- master screw
- microadjustment screw with a graduated head
- micrometer adjustment screw
- micrometer screw
- micrometer-calibrated screw
- micrometer-dial screw
- milled screw
- mirror screw
- motion screw
- motion transmission screw
- mounting screw
- multiple-thread screw
- multiple-threaded screw
- multistart screw
- mushroom-headed screw
- odd-pitch screw
- oval binding head screw
- oval countersunk head screw
- oval filister head screw
- oval head screw
- oval point set screw
- oven head screw
- pan head screw
- perpetual screw
- piano head screw
- pinched-head wood screw
- pivot screw
- plain-ended screw
- plug screw
- pointed screw
- pointless screw
- positioning ball screw
- positioning screw
- power screw
- pressing screw
- pressure screw
- pressure-adjusting screw
- prestressed recirculating ball screw
- pretensioned ball screw
- pulling-off screw
- quadruple threaded screw
- quarter turn screw
- quill clamping screw
- rail-elevating screw
- raised cheese head screw
- raised countersunk head screw
- ram-positioning screw
- rapid screw
- reamed screw
- recirculating ball lead screw
- recirculating ball screw
- register screw
- retainer screw
- retaining screw
- retension screw
- rolled race ball screw
- rough screw
- round head screw
- saddle binder screw
- seat screw
- securing screw
- self-tapping screw
- semifinished screw
- set screw with cup point
- set screw with flat point
- set screw with full dog point
- set screw with half dog point and flat cone point
- set screw with waisted shank
- setting screw
- sharp screw
- shoulder screw
- shouldered screw
- single-shoulder screw
- single-threaded screw
- slipper screw
- slotted screw
- slotted set screw
- slotted-head screw
- small raised cheese head screw
- socket head screw
- splined screw
- square head screw
- square set screw
- stop screw
- straight knurled head screw
- stretching screw
- sunk screw
- support screw
- swivel screw
- table feed screw
- table screw
- table-traversing screw
- tapping screw
- telescope screw
- thread cutting screw
- thread forming screw
- thrust screw
- thumb screw
- tight fitting screw
- tightening-up screw
- tommy screw
- transfer screw
- translation screw
- transport ball screw
- traverse screw
- traversing screw
- truss head screw
- turnbuckle screw
- turned screw
- unfinished screw
- union screw
- universal screw
- vee threaded screw
- vertical feed screw
- volume-adjusting screw
- washer head screw
- wheel screw
- whitworth screw
- wing screw
- winged screw
- wood screw
- work-holding screw
- worm screwEnglish-Russian dictionary of mechanical engineering and automation > screw
См. также в других словарях:
performing arts — arts or skills that require public performance, as acting, singing, or dancing. [1945 50] * * * ▪ 2009 Introduction Music Classical. The last vestiges of the Cold War seemed to thaw for a moment on Feb. 26, 2008, when the unfamiliar strains … Universalium
arctic — arctically, adv. /ahrk tik/ or, esp. for 7, /ahr tik/, adj. 1. (often cap.) of, pertaining to, or located at or near the North Pole: the arctic region. 2. coming from the North Pole or the arctic region: an arctic wind. 3. characteristic of the… … Universalium
List of Occupy movement protest locations in the United States — Contents 1 List 2 Gallery 3 See also 4 References … Wikipedia
Congestion pricing — Typical traffic congestion in an urban freeway. Shown here I 80 Eastshore Freeway, Berkeley, United States … Wikipedia
List of SASUKE Stages — Sasuke is a Japanese sports entertainment television special that airs on the Tokyo Broadcasting System (TBS) between Japanese television drama seasons, and consists of a competition in which 100 competitors attempt to complete four obstacle… … Wikipedia
Battery (electricity) — For other uses, see Battery (disambiguation). Various cells and batteries (top left to bottom right): two AA, one D, one handheld ham radio battery, two 9 volt (PP3), two AAA, one C, one … Wikipedia
Voice over IP — Digital voice redirects here. For the commercial service, see Comcast Digital Voice. Voice over Internet Protocol (Voice over IP, VoIP) is a family of technologies, methodologies, communication protocols, and transmission techniques for the… … Wikipedia
Madrid Metro — Info Locale Madrid Transit type Rapid transit … Wikipedia
List of Kururu's inventions — Many of the storylines in both the manga and the anime versions of Sgt. Frog happen thanks to Sgt. Major Kururu s knack for inventing. His twisted nature combined with Keroro s need to conquer Pokopen/Pekopon work fluidly together, as it gives… … Wikipedia
Metal Warriors — This article is about the video game. For the song, see The Triumph of Steel. Metal Warriors Developer(s) LucasArts Publisher(s) Konami Engine ZAMN … Wikipedia
Denver International Airport — This article is about the current airport opened since 1995. For the airport previously serving Denver, Colorado, see Stapleton International Airport. Denver International Airport … Wikipedia